SUP20S Description This intelligent 12V DC 120W electric pump comes with digital control and LCD screen to display the set pressure and real-time air pressure. It can Auto-Stop at your pre-set air pressure, or when max 20 minutes continued working time reached. So you can never over-inflate the chamber or damage the pump. Great to use for inflatable SUP and paddle board. Max 20PSI and great quality. Compatible with HR (Halkey-Roberts), Bravo or similar type air valve that suitable the most SUPs in the market. Those air valves have a turning pin or pressing down pin at the middle to control the valve's Open & Closed position. Comes with 3 different size O ring - 3mm, 5mm and 6mm. So you may be easy to find a right one that suitable for your SUP. FYI, additional SUP Air Hose Kit - Version 2 is available on Amazon or our website. Pump's 12V DC connector (Car Cigarette Lighter connector) has a built-in 10A fuse. You can connect the pump to your vehicle. Unscrew the head connector bolt can access this fuse if need exchange.
- Model: Seamax SUP20S
- Pump Support Rate: 0.5-20 PSI (0.034-1.378 Bar)
- Digital Sensor Accuracy: 0.01 PSI
- Controller Method: Pre-programmed digital controller
- Pressure Display: PSI & Kpa - Max Pumping Speed: 70L/min
- Pumping: Engineered cylinder type compressor for high pressure
- O Ring Thickness: 0.3mm, 0.5mm, 0.6mm
- Pump Working Voltage: 11-14V DC
- Max Energy Consumption: 10A, 120W (12V)
- DC Power Cord Length: 9ft (2.75m)
- Air Hose: 3.5ft Length & with HR Valve Adaptors
- Product Net Weight: 2.86 Lbs (1300g) - Warranty: 2 Years within USA & Canada
- Version 2 air hose kit for Seamax SUP Electric Pump
- Leafield C7 air valve adaptor
This intelligent DC electric air pump with a Digital pressure LCD screen is the best pump for inflatable tent, SUP, and paddle board etc. Easy to Reach High Pressure, Engineered in Canada. Max pressure can reach 20 PSI (1.378 Bar /138 Kilo-Pascal) in about 15 minutes for an inflatable paddle board. This new single stage high efficient handy air pump is with our latest standard to build.
Connect the end with Flexible conduit adaptor to the Nylon air hose (High Temperature Qualified) with the pump inflation outlet and twist clockwise to tighten it. Install the supported valve adaptor to the other end of the hose, and twist clockwise to tighten it. Then connect this air hose to the chamber and ready to go.
After connecting with the power, the pump will be turned on, LCD screen is showing the reading pressure. Press the Pressure Unit button to select the pressure unit PSI or Bar. Use the Pressure Increase button (+) or Pressure Decrease button (-) to set your needed pressure. The range of pressure value is from 0.5 to 20PSI, (1PSI=0.0689BAR). Increasement is 0.5 PSI. After finishing the above steps, press the power On/Off button to start the pump.
During the inflating process, you can be easy to increase or reduce the set pressure value without stopping the current pumping. Use the Unit button to switch the pressure reading in any time. Press the On/Off button to stop the pump. Pump maximum continued working time is 20 minutes in its program, and the pump can turn off by itself when 20 minutes reached. You can manually turn on the pump once again if you need more works.
This pump has built in a digital pressure gauge to do the real time monitoring. When the pressure reading can reach the pump set value, the air pump will stop automatically. You can make sure the pressure is good before you disconnect the air hose from the chamber. When the application is 20PSI, the air hose connector will turn very tight when disconnecting. This is normal.